Passport USB Interface (COM3) Driver Download For Windows 10



Click the Download button on this page to start the download; Do one of the following: To start the installation immediately, click Run. To save the download to your computer for installation at a later time, click Save. To cancel the installation, click Cancel. Western Digital My Passport Go Mac Driver. Once you physically connect your My Passport Go and the Mac system, you have to download the drivers and install them on your system. To download the compatible driver file, you have to specify the OS version as Mac. When the Download button is displayed on the next screen, click on it to download the.

  1. Passport USB Interface (COM3) Driver Download For Windows 10
  2. Passport Usb Interface (com3) Driver Download For Windows 10 Windows 10
  3. Passport Usb Interface (com3) Driver Download For Windows 10 64

Virtual COM Port Drivers for Ross-Tech USB Interfaces

Older Ross-Tech RS-232 Serial interfaces can be set to power up as 'dumb K-Line pass through' interfaces. This allowed those old Serial interfaces to be compatible with a wide variety of third-party applications which expect a 'K-line pass-through' serial interface. However, our USB interfaces present additional challenges. Early in their development, we found a number of technical advantages to using a 'direct' USB driver which bypasses the Windows Serial drivers entirely. Hence the USB drivers that ship with VCDS do not emulate a serial COM port and cannot be used with applications that expect to communicate via a serial port.
NOTE: The following applies to our legacy USB interfaces (HEX-USB, KII-USB and HEX-USB+CAN). It does NOT apply to our current HEX-V2 or HEX-NET interfaces. These new interfaces do not use a USB UART chip and cannot be be used for 'dumb K-line pass-through'!

(com3)Passport usb interface (com3) driver download for windows 10 64-bit

In order to facilitate the use of third-party applications which expect to communicate with a serial interface, drivers that emulate a COM port are available. However, anyone thinking about using them needs to be aware of the following points:

  • We do not offer installation support for these drivers. They should be used only by someone who is competent/comfortable installing (and possible uninstalling) USB drivers on his PC.

  • We cannot offer any support for third-party software, nor any guarantee that it will work correctly with these drivers. Of course, the same would apply with a serial interface as well.

That said, here some installation notes:

  • These drivers are compatible with Windows 2000 and newer. They should work with W2K, XP-32, XP-64, Vista-32 and Vista-64. We do not have any VCP drivers for Windows 98!

  • Unzip the contents of the download into a new folder.

  • With an interface plugged in, find it in Device Manager, right-click it, and select Update Driver.

  • Depending on what drivers your system already has installed, you may have to 'force' these by telling the wizard not to search, but to let you specify what driver to install, then doing the Have Disk and Browse thing.

  • There's also the possibility that the Virtual COM Port won't install automatically. We've found no real pattern why it does on some systems and not on others. If it does not, find the interface in Device > Manager. The name should show '... with VCP'. Open the properties sheet, click the Advanced tab, and make sure Load VCP is checked. Once checked, disconnect and re-connect the interface.

  • Once the USB Serial Port is installed, you may need to change the COM Port Number (depending on how high a number the applications supports). Device Manager, Properties sheet for the USB Serial Port, Port Settings tab, Advanced button. The COM Port Number may change if you plug the interface into a different USB port, so I'd recommend always using the same USB port.

  • VCDS should continue to work fine with these drivers installed. Leave VCDS set to USB, not a Virtual COM Port!

Assuming you've read and understand all of the above, you can download the 'Virtual COM Port' drivers here:

Interface

Home
Products
 VCDS
Product Information
Interfaces
TWIN-USBKII-USB HEX-USB+CAN
Virtual COM Port Drivers

-->

This article helps to fix an issue in which Windows 10 doesn't install specific drivers for USB audio devices on the first connection.

Original product version: Windows 10, version 1703
Original KB number: 4021854

Symptom

When you connect a USB audio device to a Windows 10 Version 1703-based computer the first time, the operating system detects the device but loads the standard USB audio 2.0 driver (usbaudio2.sys) instead of the specific device driver.

Cause

This issue occurs because the USB audio 2.0 driver (usbaudio2.sys) isn't classified as a generic driver in Windows 10 Version 1703. Therefore, the system assumes that a compatible, nongeneric driver is installed for the device even though the driver is generic.

This issue also causes Windows 10 Version 1703 to postpone the search for other compatible drivers through Windows Update that typically occurs immediately after you install a new device.

Resolution

To fix this issue, use one of the following methods.

Method 1

To resolve this issue, install update 4022716.

Method 2

If the device-specific driver is distributed through Windows Update, you can manually update the driver by using Device Manager. For more information about how to do this, see update drivers in Windows 10.

Passport USB Interface (COM3) Driver Download For Windows 10

Method 3

If the device is not yet connected, first install the device-specific driver, such as by using the appropriate installer. After the device-specific driver is installed, Windows 10 will select that driver instead of the standard USB audio 2.0 driver when you first connect the device.

Note

See the device manufacturer's user guide for specific instructions about how to install the driver.

Method 4

If the driver isn't distributed through Windows Update, you can manually reinstall the driver. To do this, follow these steps:

Passport Usb Interface (com3) Driver Download For Windows 10 Windows 10

  1. Install the device-specific driver (see Method 2).
  2. Open Device Manager.
  3. Right-click (or tap and hold) the name of the device, and then select Uninstall.
  4. Restart the computer.

Passport Usb Interface (com3) Driver Download For Windows 10 64

When it restarts, Windows will try to reinstall the device by using the device-specific driver.